Electrical Onboarding/PSoC getting started (Blink)

PSoC (Programmable System on Chip) is a powerful microcontroller platform that provides flexible hardware functionality in addition to the same software functionality you get with other micro controllers.

PSoC Microcontrollers

Most microntroller platforms (eg. Arduino, PIC) have fixed hardware peripherals the developer has access to, as well as a CPU that can execute software commands written in a language such as C. PSoC offers all of this plus reconfigurable hardware and interconnect fabric to allow almost any hardware device to be routed to almost any general purpose input/output (GPIO) pin on the device. Additionally, PSoC also offers analog component blocks such as digital to analog converters (DACs), analog to digital converters (ADCs), and amplifiers.

Setting up the project

PSoC Creator project creation

To begin working with PSoC, download PSoC Creator. This is an IDE that will allow you to create new PSoC projects and program your PSoC mircrocontroller. Create a new project by clicking File and selecting New Project. For this project we will assume you are using the PSoC 5 development boards used in the microcontrollers class (CY8CKIT-059), so select this as the target kit (see the image above). At the next dialog, select an Empty project, and click next. Then give your workspace and project a name (eg. Blink Workspace, Blink Project). A project is simply a design to be implemented on some PSoC hardware device, while a workspace is a container for multiple projects. For this example we will only have a single project within the workspace, but you could possibly have more (eg. a bootloader program and a bootloadable project).

Once your project is created you will be presented with a white box with a dotted grid. This is a blank schematic sheet where hardware peripherals can be added from the component catalog on the right hand of the screen. You will also see you workspace explorer where all workspace files can be found on the left hand of the screen. For this design the only hardware component that will be needed is a digital output pin. Add the pin component from the catalog folder Ports and Pins to your schematic and double click on the schematic component to configure it as shown in the figure below. Change the name of the pin component to LED_PIN to give it some contextual meaning in the project.

Blue shows the schematic component symbol, red shows the catalog entry, and orange shows the pin configuration settings

Blinking an LED with code

In PSoC you can blink an LED using software or hardware. Let's begin by usin software. First, let's assign our pin component in the schematic to an appropriate device pin on the chip. To do this, look at the workspace explorer on the left and select the Pins entry. Configure your pin to use P2[1] (ie. device pin 63). This is pin is already connected to an LED on the PSoC 5 development board. Your pin menu should look like the picture below.

PSoC pin assignment menu

Once the pin is assigned click on the Build menu and select Generate application. This will tell PSoC creator to create code APIs that you can use in your software to make things easier. Next double click the main.c file in the workspace explorer so that we can begin writing code. Enter the following code into your main.c file.

#include "project.h"

int main(void)
{
    CyGlobalIntEnable; /* Enable global interrupts. */

    /* Place your initialization/startup code here (e.g. MyInst_Start()) */

    for(;;)
    {
        LED_PIN_Write(1);
        CyDelay(1000);
        LED_PIN_Write(0);
        CyDelay(1000);
    }
}

Let's analyze this code to see what it is actually doing.

This line includes the generated code APIs that are defined in project.h.

#include "project.h"

This code enables interrupts on the device. Below this is where any initialization and setup routine code would be placed if any were needed. In this example no setup is required.

CyGlobalIntEnable; /* Enable global interrupts. */

/* Place your initialization/startup code here (e.g. MyInst_Start()) */

This code drives the pin to a logic 1 (3.3V on PSoC5 devices) using the generated API macro LED_PIN_Write(1). It then delays program execution for 1000 milliseconds with the API macro CyDelay(). It repeats this process to drive the pin to a logic 0 (0V/GND). This will give the effect of having the PSoC board's LED blink at a rate of 0.5 Hz (on for 1 second, off for 1 second). The for(;;) loop condition makes it so this code will be repeated indefinitely as long as the device has power.

for(;;)
{
    LED_PIN_Write(1);
    CyDelay(1000);
    LED_PIN_Write(0);
    CyDelay(1000);
}

An important thing to note is that the generated code APIs use the names you provide to the components in the schematic. If you changed your LED_PIN to be named LIGHT, for example, the code would change to the following:

for(;;)
{
    LIGHT_Write(1);
    CyDelay(1000);
    LIGHT_Write(0);
    CyDelay(1000);
}

Once you understand this code well enough, go ahead and program the PSoC. Plug the board's USB connector end into a USB port on your PC. Then select Debug and Program. The dialog box should autodetect your PSoC device, so just click program and your code should upload to the PSoC and the LED should begin blinking immediately.

Try adding four LEDs to a breadboard circuit with 1K ohm resistors in series. Connect the anode of each LED to a PSoC pin as shown in the schematic below. Write some code to create a binary counter that will count up every one second, and reset to 0 once a value of 0xF (15 in decimal) is reached. In the PSoC Creator schematic, call each of your pins LED0, LED1, LED2, and LED3 in order to match the solution code.

Binary LED counter schematic using PSoC5

Solution

#include "project.h"

int main(void)
{
    int count = 0;
    char pin_val[4];

    CyGlobalIntEnable; /* Enable global interrupts. */

    /* Place your initialization/startup code here (e.g. MyInst_Start()) */

    for(;;)
    {
        pinval[0] = count&1;
        pinval[1] = (count&2)>>1;
        pinval[2] = (count&4)>>2;
        pinval[3] = (count&8)>>3;

        LED0_Write(pinval[0]);
        LED1_Write(pinval[1]);
        LED2_Write(pinval[2]);
        LED3_Write(pinval[3]);

        CyDelay(1000);
    }
}